ISO 50001 energy performance indicators and energy baselines on AVEVA PI data

ISO 50001 asks for one thing above all: proof that your energy performance improves. That proof rests on two building blocks, energy performance indicators (EnPIs) and energy baselines (EnBs). ISO 50001:2018 requires both, and ISO 50006, revised in 2023, gives guidance on how to build them.

Most industrial sites already record the data they need in the AVEVA PI System: meters, production counters, temperatures and operating states, at high resolution and over many years. This article shows how to turn that data into EnPIs and energy baselines that hold up in an audit, and where energy:center automates the work.

What ISO 50001 means by EnPIs and energy baselines

  • Energy performance indicator (EnPI): a measure of energy performance that you define, for example the steam consumption of a dryer or the electricity per tonne of product.
  • Energy baseline (EnB): the reference you compare against, usually built from a baseline period of about one year that represents normal operation.
  • Relevant variables: factors that change routinely and affect energy use significantly, such as production volume, outdoor temperature or product mix.
  • Static factors: factors that normally stay the same, such as installed equipment or site boundaries. When they change significantly, the baseline has to be adjusted.

An EnPI on its own only describes. Compared with the baseline, it shows whether energy performance has improved.

Common ways to express an EnPI

  • Measured energy value: total consumption per period, for example monthly gas use. It works where nothing else drives consumption.
  • Ratio of measured values: specific energy consumption, for example kWh per tonne. It is easy to explain but misleading when a large base load does not scale with output.
  • Statistical model: a regression of energy use against relevant variables such as production and degree days. The model predicts expected consumption, and the gap to actual consumption is your normalised saving.
  • Engineering model: a physics-based model for complex systems where data alone is not enough.

For most significant energy uses in process plants, a regression model on production and weather data gives the most honest picture, because it separates real improvement from changes in output or season.

Building EnPIs and baselines from AVEVA PI data

  1. Map energy flows in PI Asset Framework. Model meters, significant energy uses and relevant variables as attributes in AF templates, so every line, unit and site follows the same structure.
  2. Check data quality. Find gaps, stuck values, counter resets and unit errors, and reconcile meter totals with utility invoices.
  3. Choose the baseline period. Take about twelve months of normal operation and document every period you exclude, such as shutdowns.
  4. Build and test the model. Fit a regression of energy use against the relevant variables for each significant energy use, and check that the model explains consumption well before you rely on it.
  5. Compare expected and actual. For every reporting period, compare actual consumption with what the baseline model expects. A cumulative sum (CUSUM) chart shows whether savings hold.
  6. Report and maintain. Report EnPIs monthly, and adjust the baseline when static factors change, for example after a new production line.

Where energy:center helps

energy:center is Amitec’s energy management system on the AVEVA PI System. It calculates EnPIs and energy baselines automatically from your existing PI data, validates energy data against commercial records and utility benchmarks, and produces the reports you need for ISO 50001 audits. AI-based analytics flag unusual consumption early, and energy managers, plant teams and group management see the same validated figures for every site.

See how EGGER runs group-wide energy management with AVEVA PI and energy:center, and read what Germany’s Energy Efficiency Act (EnEfG) requires from companies with an ISO 50001 obligation.

Frequently asked questions

How many EnPIs do we need?

ISO 50001 does not prescribe a number. You need enough EnPIs to measure and monitor the energy performance of your significant energy uses, and to show improvement for the organisation as a whole.

Do we need high-resolution data?

Monthly values are often enough for reporting. Higher resolution helps you find causes, for example consumption during idle times or at night, and PI usually has it already.

When does the energy baseline have to be adjusted?

ISO 50001 requires an adjustment when EnPIs no longer reflect energy performance, when static factors change significantly, or according to a method you defined in advance.

Talk to an energy expert

Tell us about your sites and meters, and we will show you how energy:center works with your PI data.

energy:center

ISO 50001 energy management on the AVEVA PI System.

Want to know more?

Featured product

Amitec Industrial Knowledge Graph product box

Related posts